Pulpdent Porcelain Prep Kit

Pulpdent Porcelain Prep Kit

Pulpdent

Availability: Sold out

For Preparing Porcelain Surfaces for Bonding
New Rs. 2300

Rs.2,500.00

Rs.2,300.00

Description

Details

This economical kit for preparing porcelain surfaces for bonding contains Porcelain Etch Gel, Kool-Dam™, Silane and Drying Agent. Use with your preferred composite or resin cement. The one-minute application of Porcelain Etch Gel will not stain the ceramic.

  • For Preparing Porcelain Surfaces for Bonding
  • Contains Porcelain Etch Gel, Silane, Kool-Dam and Dry-Rite Drying Agent

This economical kit for preparing porcelain surfaces for bonding contains Porcelain Etch Gel, Kool-Dam™, Silane and Drying Agent. Use with your preferred composite or resin cement. The one-minute application of Porcelain Etch Gel will not stain the ceramic.

  • For Preparing Porcelain Surfaces for Bonding
  • Contains Porcelain Etch Gel, Silane, Kool-Dam and Dry-Rite Drying Agent
Features
  • For Preparing Porcelain Surfaces for Bonding
  • Protect soft tissue with Kool-Dam
  • One-minute application will not stain the ceramic
  • Contains Porcelain Etch Gel, Silane, Kool-Dam and Dry-Rite Drying Agent
Directions to use

1. Protective eyewear must be worn by practitioner, assistant and patient. Protective gloves must be worn by practitioner and
assistant.
2. Place rubber dam to isolate operative site and protect soft tissue.
3. Securely attach a green 18-gauge applicator tip to the Kool-Dam and apply a coat of Kool-Dam 1-2 mm thick on the gingiva or
tooth surfaces requiring protection, if needed.
4. Light cure for 10 seconds. Cures with all lights.
5. Assistant must stand ready at chairside and hold vacuum tip 2-3 inches from porcelain surface during the etching process to
evacuate acid fumes.
6. Securely attach a 25-gauge applicator tip to the Porcelain Etch Gel syringe. Carefully start the flow of Porcelain Etch Gel on
a pad and immediately dispose of this sample. Do not start flow in patient’s mouth. For maximum control of flow, do not push
on plunger with thumb. It is recommended instead to hold syringe barrel between thumb and forefinger while resting plunger in
palm of hand. Gently pull back with thumb and forefinger to start flow. Never force plunger. Use a new applicator tip for each
patient.
7. Carefully apply Porcelain Etch Gel to porcelain surface and leave for one minute while evacuating fumes with vacuum. Cap
syringe immediately after use.
8. Remove etch gel with vacuum. Rinse treated surface with copious amounts of water and dry with clean, uncontaminated, oil-free
and moisture-free compressed air.
9. Securely attach red dropper tip to the Dry-Rite syringe and apply Pulpdent Dry-Rite drying agent to treated surface. To promote
rapid drying, use a gentle flow of clean, oil-free air if desired. Cap Dry-Rite immediately after use.
10. Securely attach red dropper tip to Silane syringe and apply Pulpdent Silane Bond Enhancer to the etched ceramic surface and
allow to dry. Apply a gentle flow of clean, oil-free and moisture-free air, if desired. Cap syringe immediately after use.
11. Proceed with repair or cementation of porcelain teeth, inlays or veneers using your preferred unfilled resin bonding agent and
restorative resin or resin cement.


packaging
  • 2 x 1.2 mL syringe each Porcelain Etch Gel and Silane,
  • 1 x Kool-Dam 
  • 1 x Drying Agent 
  • Applicator tips
Additional Information

Additional Information

Dispatch Date Next Day
COD Yes
FAQs N/A
Reviews

Related Products

There are no products matching the selection.

Recently Viewed Products