SDI Stae Bond

SDI Stae Bond

Sdi

Availability: In stock

Total Etch Bond
New Rs. 1250

Rs.1,750.00

Rs.1,250.00

bulk price: Rs.1,150.00
  • Buy 2 or above for Rs.1,200.00 each and save 4%
  • Buy 5 or above for Rs.1,150.00 each and save 8%

Check COD
  • Enter pincode to check whether Cash On Delivery is available.
  • Delivery available at all pincodes.
  • Generally delivered in 4 - 5 working days.
  • Free Shipping Above ₹2500.
  • COD Not available for Order Above ₹20000 or Above 10Kg.



OR
Description

Details

Stae is a fluoride releasing single component dentin / enamel total - etch adhesive system, designed for direct bonding. Stae completely and homogeneously infiltrates the hybrid layer to ensure superior bonding to the tooth.

COMPOSITION:

Acrylic monomer Acetone Fluoride Stabilizer

INDICATIONS:

I) All direct restorative composites

II) Compomers III) Composite / Ceramic+ / Metal+ / Porcelain+ repairs. + Bonding surface requires pre-treatment with a silane primer.

CONTRAINDICATIONS:

I) Not to be used in combination with chemically-cured composite resin

II) Do not use for pulp capping

III) Any persons having known resin allergies should refrain from using Stae

IV) Not to be used in combination with eugenol materials or hemostatics containing ferric compounds

V) Not to be used in combination with desensitising agents.

Stae is a fluoride releasing single component dentin / enamel total - etch adhesive system, designed for direct bonding. Stae completely and homogeneously infiltrates the hybrid layer to ensure superior bonding to the tooth.

COMPOSITION:

Acrylic monomer Acetone Fluoride Stabilizer

INDICATIONS:

I) All direct restorative composites

II) Compomers III) Composite / Ceramic+ / Metal+ / Porcelain+ repairs. + Bonding surface requires pre-treatment with a silane primer.

CONTRAINDICATIONS:

I) Not to be used in combination with chemically-cured composite resin

II) Do not use for pulp capping

III) Any persons having known resin allergies should refrain from using Stae

IV) Not to be used in combination with eugenol materials or hemostatics containing ferric compounds

V) Not to be used in combination with desensitising agents.

Features

One bottle system

Stae combines both primer and adhesive in one bottle to simplify the technique and decrease patient chair time.

Fluoride release

Fluoride’s cariostatic effect enhances remineralization and inhibits enamel demineralization. In an aqueous environment, the fl uoride ions in Stae diffuse from the resin into the surrounding tooth. This ionic movement is caused by oral fl uid passing in and out of the resin and tooth, acting as a carrier for the fl uoride ions.

Non Bis-phenol A

Stae avoids the Bis-phenol A hormonal imbalance controversy, as it does not contain the related BisGMA resin.

Bonds to moist and dry tooth surfaces

Stae’s carrier solvent is a mixture of acetone and water. The acetone carries Stae deep into the demineralized dentin and the water re-moistens any dry dentin.

High bond strength

Stae’s complete hybridization of the resin into the demineralized dentin results in high bond strength.

Directions to use

1. Clean and isolate tooth. Rubber dam is the preferred mode of isolation

2. Prepare a conservative cavity, employing standard techniques

3. Use a calcium hydroxide liner and appropriate glass ionomer cement liner to protect deep cavity preparations in close proximity to the pulp

4. Thoroughly dry the bonding surfaces of the tooth with dry, oil-free air

5. Etch with Super Etch 37% phosphoric acid (SDI Limited) for at least 20 seconds.

NOTE: Enamel subjected to fluoridation should be etched for 90 to 120 seconds.

IMPORTANT: If using an etch syringe, ensure that the dispensing tip hub is firmly attached to the syringe by twisting the hub securely onto the syringe. On first usage or after prolonged storage, extrude a small amount onto a mixing pad for familiarity with the etchant’s viscosity and rate of extrusion. 6. Wash thoroughly with water.

7. Remove excess water. Keep moist. Avoid contamination e.g. saliva.

8. Apply Stae to saturate all internal surfaces

9. Blow gently with dry, oil-free air to evaporate solvent. Leave surface glossy

10. Light cure for 10 seconds.

NOTE: do not polymerize Stae by itself in a mixing well; it will be a non – polymerized looking material. Stae contains a unique hydrophobic and hydrophilic monomer that does not cure when exposed to oxygen. The product will polymerize once covered by any lightcure composite restorative material

11. Place composite in increments of 2mm or less.


packaging
  • 1 x 5ml Stae bottle
Additional Information

Additional Information

Dispatch Date Next Day
Reviews

Hot Selling

Sdi Pola Office 1 Patient Kit
sdi pola office 1 patient kit
In Office Bleaching Kit (35% Hydrogen Pe...
  • Rs.3,300.00

    Rs.2,995.00

    bulk price: Rs.2,975.00
    9.2% off
Sdi Pola Office Plus 1 Patient Kit
sdi pola office plus 1 patient kit
Bleaching Agent (37% Hydrogen Peroxide)
  • Rs.3,600.00

    Rs.3,200.00

    bulk price: Rs.3,100.00
    11.1% off
Sdi Pola Office Plus
sdi pola office plus
Bleaching Agent (37% Hydrogen Peroxide)
  • Starting at: Rs.3,200.00

    11.1% off
Sdi Luna Composite
sdi luna composite
Composite Restorative Material
  • Starting at: Rs.625.00

    30.6% off
Sdi Wave Flowable Composite
sdi wave flowable composite
Flowable Composite
  • Starting at: Rs.385.00

    30% off
Sdi Wave Flowable Composite MV
sdi wave flowable composite mv
Flowable Composite
  • Starting at: Rs.390.00

    29.1% off
SDI Super Etch Etchant Gel
sdi super etch etchant gel
Etchant
  • Starting at: Rs.190.00

    5% off
SDI Set PP Resin Cement
sdi set pp resin cement
Self Cure Resin Cement
  • Starting at: Rs.3,450.00

    6.8% off
Sdi Riva Self Cure GIC
sdi riva self cure gic
Self Cure GIC
  • Starting at: Rs.1,560.00

    32.2% off
SDI PolaNight Bleaching Kit
sdi polanight bleaching kit
Home/InOffice Bleach
  • Starting at: Rs.2,765.00

    4.7% off

Related Products

There are no products matching the selection.

Recently Viewed Products