Sdi Wave Flowable Composite

Sdi Wave Flowable Composite

Sdi

Availability: In stock

Flowable Composite
New Rs. 385

Starting at: Rs.385.00

Sdi Wave Flowable Composite A1
  • Buy 2 or above for Rs.380.00 each and save 2%
  • Buy 5 or above for Rs.370.00 each and save 4%

Rs.550.00

Rs.385.00

bulk price: Rs.370.00
Sdi Wave Flowable Composite A2
  • Buy 2 or above for Rs.380.00 each and save 3%
  • Buy 4 or above for Rs.375.00 each and save 4%

Rs.550.00

Rs.390.00

bulk price: Rs.375.00
Sdi Wave Flowable Composite OA2

Rs.550.00

Rs.390.00

Sdi Wave Flowable Composite A3.5

Sold out

Rs.550.00

Rs.390.00

Sdi Wave Flowable Composite B1

Rs.550.00

Rs.390.00


OR
Description

Details

Wave is the ideal versatile fluoride releasing, flowable, radiopaque, light cured composite. Wave is directly injected into the cavity preparation for maximizing adaptation to the preparation. The Wave shade range consists of 14 popular shades - enamel A1, A2, A3, A3.5, B1, B2, B3, C2, C3, D3, incisal, gingival, bleach; and 0A2 dentin shade. Enamel shades can be guided by VITA classical shade guide. Gingival shade is ideal for restoring cervical lesions in elderly patients. For teeth lighter than B1, bleach shade is available.

A choice of 3 viscosities-Wave,Wave MV (Medium Viscosity),Wave HV (High Viscosity) . Wave, Wave MV and Wave HV contain specially treated nano-fillers to maximize polishability, wear resistance and strength. Ease of extrusion is improved with the addition of these specially treated nano-fillers.

COMPOSITION WAVE:

35% wt (52 Vol%) multifunctional methacrylic ester

65% wt (41 Vol%) (0.02 - 10 micron) inorganic filler

COMPOSITION WAVE MV:

40% wt (61 Vol%) multifunctional methacrylic ester

60% wt (39 Vol%) (0.02 - 10 micron) inorganic filler

COMPOSITION WAVE HV:

34% wt (53 Vol%) multifunctional methacrylic ester

66% wt (44 Vol%) (0.02 - 10 micron) inorganic filler 

INDICATIONS:

  • Class V restorations
  • Tunnel / air abrasion preparations
  • Pit and fi ssure sealants
  • Minimal Class I, II, III, IV restorations
  • Radiopaque cavity liners
  • Cervical abrasion/erosion lesions
  • Abfraction lesions
  • Implant seals
  • Incisal abrasions
  • Repair enamel defects
  • Minor core build-ups
  • Temporary crowns
  • Cement porcelain/ceramic/ composite veneers
  • Splint mobile teeth
  • Attach fiber bridges
  • Restorations in deciduous teeth
  • Repair porcelain restorations
  • Block out undercuts in inlay/onlay/crown preparations
  • Cover stains
  • Adhering tooth jewelry
  • Ceramic inserts

Wave is the ideal versatile fluoride releasing, flowable, radiopaque, light cured composite. Wave is directly injected into the cavity preparation for maximizing adaptation to the preparation. The Wave shade range consists of 14 popular shades - enamel A1, A2, A3, A3.5, B1, B2, B3, C2, C3, D3, incisal, gingival, bleach; and 0A2 dentin shade. Enamel shades can be guided by VITA classical shade guide. Gingival shade is ideal for restoring cervical lesions in elderly patients. For teeth lighter than B1, bleach shade is available.

A choice of 3 viscosities-Wave,Wave MV (Medium Viscosity),Wave HV (High Viscosity) . Wave, Wave MV and Wave HV contain specially treated nano-fillers to maximize polishability, wear resistance and strength. Ease of extrusion is improved with the addition of these specially treated nano-fillers.

COMPOSITION WAVE:

35% wt (52 Vol%) multifunctional methacrylic ester

65% wt (41 Vol%) (0.02 - 10 micron) inorganic filler

COMPOSITION WAVE MV:

40% wt (61 Vol%) multifunctional methacrylic ester

60% wt (39 Vol%) (0.02 - 10 micron) inorganic filler

COMPOSITION WAVE HV:

34% wt (53 Vol%) multifunctional methacrylic ester

66% wt (44 Vol%) (0.02 - 10 micron) inorganic filler 

INDICATIONS:

  • Class V restorations
  • Tunnel / air abrasion preparations
  • Pit and fi ssure sealants
  • Minimal Class I, II, III, IV restorations
  • Radiopaque cavity liners
  • Cervical abrasion/erosion lesions
  • Abfraction lesions
  • Implant seals
  • Incisal abrasions
  • Repair enamel defects
  • Minor core build-ups
  • Temporary crowns
  • Cement porcelain/ceramic/ composite veneers
  • Splint mobile teeth
  • Attach fiber bridges
  • Restorations in deciduous teeth
  • Repair porcelain restorations
  • Block out undercuts in inlay/onlay/crown preparations
  • Cover stains
  • Adhering tooth jewelry
  • Ceramic inserts
Features

Nanofilled

Wave, Wave MV and Wave HV contain specially treated nano-fi llers to maximize polishability, wear resistance and strength. Ease of extrusion is improved with the addition of these specially treated nano-fi llers.

Filler loading

Wave, Wave MV and Wave HV all have excellent wear profi les due to their high fi ller loading level:

Fluoride release

Fluoride’s cariostatic effect enhances remineralization and inhibits enamel demineralization. In an aqueous environment, the fl uoride ions in Wave, Wave MV and Wave HV diffuse from the resin into the surrounding tooth. This ionic movement is caused by oral fl uid passing in and out of the resin and tooth, acting as a carrier for the fl uoride ions.

Natural fluorescence

Wave, Wave MV and Wave HV contain a fl uorescent agent that ensures perfectly natural looking teeth under ultraviolet lights. No one will know!

Radiopacity

Wave, Wave MV and Wave HV are all visible on x-rays. This allows easy identifi cation of secondary caries at the interface.

Compressive strength

Wave’s, Wave MV’s and Wave HV’s high compressive strength values expand the suitability for multiple applications.

UDMA

Wave’s UDMA resin system minimizes shrinkage and reduces post operative sensitivity.

Tip length comparison

Wave’s complet tip length is 12.2mm, 40% longer than the alternative of 8.7mm. Wave’s longer tip length allows more direct placement of the material into diffi cult to reach areas.

Video
Directions to use

Clean and Isolate tooth. A conservative cavity should be prepared, employing standard techniques and instruments, to form a slightly rounded internal form. Margins of the cavity preparation should end in sound and supported enamel with no bevels in stress bearing locations. If bevelling is desired in a low stress location it should extend no further than 1mm at an angle of no greater than 45°. Pre-wedging is also recommended to ensure that the restored tooth will have an adequate contact point. Prophy all surfaces to be etched including surfaces adjacent to the cavity with an oil free non-fluoride containing paste or a slurry of pumice and water. Rinse thoroughly with water.

Shade Selection

Shade selection should be made with a just cleaned and moist tooth.

NOTE: Do not use uncured paste for color matching as there is a slight color change upon curing.

Isolation

Isolation techniques must be used to prevent contamination. Rubber dam is the preferred mode of isolation.

Pulp Protection

For deep cavities, use a calcium hydroxide liner and appropriate glass ionomer cement liner to protect deep cavity reparations in close proximity to the pulp.

1. Acid Etching

Thoroughly dry the surface to be etched with dry, oil-free air. Etch tooth surface with Super Etch 37% phosphoric acid.

(a) Enamel only Etch surface for at least 20 seconds

(b) Dentin and enamel Using the “total etch” technique etch the surface including any glass ionomer for at least 20 seconds. Enamel subjected to fluoridation should be etched for 90 to 120 seconds. Etching Precautions: Ensure that the dispensing tip hub is firmly attached to the syringe by twisting the hub securely onto the syringe. Avoid acid contact with oral tissues, eyes and skin. If accidental contact occurs wash thoroughly with water. In the case of eye contact, wash eye for 15 minutes and seek medical attention. Use matrix strips to protect adjacent tooth surfaces during etching. On first usage or after prolonged storage, extrude a small amount onto a mixing pad for familiarity with the etchant’s viscosity and rate of extrusion

2. Wash thoroughly with water

3. Remove excess water. Keep moist. Avoid contamination e.g. saliva

4. Apply Stae dentin/enamel adhesive to saturate all internal surfaces, or bonding agent according to manufacturer’s instructions

5. Blow gently with dry, oil-free air for 2 seconds to evaporate solvent. Leave surface glossy

6. Light cure for 20 seconds (460-480nm wavelength, high power LED curing light)

7. Directly inject Wave in increments of 2mm or less in: 7.1 Class V restorations, 7.2 Tunnel preparations, 7.3 Pit and fissures sealants, 7.4 Minimal Class I, Class II, Class III and Class IV restorations. Or other indication as required.

CAUTION: ensure that the dispensing tip is firmly attached to the syringe by twisting the tip hub securely onto the syringe.


packaging
  • 1 x 1g Syringe
  • 5 x disposable tips.
Expiry

Expiry date: 2020-01-01

Additional Information

Additional Information

Dispatch Date Next Day
COD Yes
Reviews

Customer Reviews 1 item(s)

Value for money

Quality is superb, almost near to costly ones

Related Products

There are no products matching the selection.

You may also be interested in

Shofu Glasionomer Fx-Ii Improved 1-1 Set
shofu glasionomer fx-ii improved 1-1 set
Glass Ionomer Restorative (Shade A2)
  • Rs.3,000.00

    Rs.2,850.00

    5% off
Dentsply Aquacem 30g
dentsply aquacem 30g
Glass Ionomer Luting Cement
  • Rs.3,570.00

    Rs.3,153.00

    11.7% off

Sold out

Shofu P & R Repair Kit
shofu p & r repair kit
Light-Cure Bonding System
  • Rs.7,800.00

    Rs.6,255.00

    19.8% off
Diadent Paper Point Special Tapered 4%
diadent paper point special tapered 4%
Paper Points
  • Starting at: Rs.205.00

    33.9% off
Gc Gold Label 1 Glass Ionomer Mini Pack(Expiry 2020)
gc gold label 1 glass ionomer mini pack(expiry 202...
Glass Ionomer Luting Cement
  • Rs.1,550.00

    Rs.1,400.00

    9.7% off
API Stainless Steel Reamers 21mm
api stainless steel reamers 21mm
Reamers
  • Starting at: Rs.170.00

    34.6% off
Prevest Micron Superior
prevest micron superior
Glass Ionomer Restorative Cement
  • Rs.1,050.00

    Rs.840.00

    20% off
Ivoclar Cention N
ivoclar cention n
Restorative Material
  • Starting at: Rs.2,840.00

    21.8% off
Top Dent Band Pinching Plier
top dent band pinching plier
Top Dent Band Pinching Plier
  • Rs.5,500.00
SDI Riva Light Cure Glass Ionomer Cement
sdi riva light cure glass ionomer cement
Resin Cement
  • Starting at: Rs.4,100.00

    8.9% off

Recently Viewed Products