Sun Medical Hybrid Bond

Sun Medical Hybrid Bond

Indian

Bonding Agent
New Rs. 3200

Rs.4,000.00

Rs.3,200.00

Reward points64 i These are the coins gained on 1 quantity of the product ordered. These points will transfer in to your account after successful delivery of your order. Know more




OR
Description

Details

Hybrid Bond is a single-bottle, self-etching, self-priming, light-cured dentin bonding system. It does not require acid-etching of dentin or cut enamel surfaces before use.* It is suitable for use with directly applied composite resins and can be cured by any light-curing devices. Hybrid Bond can also be used as the adhesive agent for indirectly fabricated restorations. It contains 4-META**, a high performance adhesive monomer that decalcifies tooth substrate and penetrates through the smear layer to form a hybrid layer, creating excellent bonds to dentin and enamel. It forms a fortified resin coat on dentin, which blocks mechanical and biological stimuli to dentin-pulp-complex. 

4-methacryloxyethyl trimellitate anhydride

 

ADVANTAGES:

EASY, 35-SECOND BONDING

No etching, just one coat 

THIN BUT ROBUST FILM

Only 9 microns but almost no post-op sensitivity Though only a single application is required, the robust coat blocks both mechanical and chemical stimuli to dentin-pulp complex. The thin bonding layer results in aesthetic margins and perfect contacts between adjacent teeth.

HIGH BOND STRENGTH

Strong bonds to enamel, dentin and resin composite... thanks to its 4-META monomer Hybrid Bond penetrates the tooth to form 4-META hybrid layer and leaves the surface protective by a robust resin film.

INDICATIONS:

Hybrid Bond can be used in

Direct restorations of all types of composites:-

  • Class I , III, IV V cavities
  • Attrition at cutting edges
  • Diastema Closure

Indirect restorations:

As a protective coat for dentin under crown & bridge work for prevention of post-op pain

 

Hybrid Bond is a single-bottle, self-etching, self-priming, light-cured dentin bonding system. It does not require acid-etching of dentin or cut enamel surfaces before use.* It is suitable for use with directly applied composite resins and can be cured by any light-curing devices. Hybrid Bond can also be used as the adhesive agent for indirectly fabricated restorations. It contains 4-META**, a high performance adhesive monomer that decalcifies tooth substrate and penetrates through the smear layer to form a hybrid layer, creating excellent bonds to dentin and enamel. It forms a fortified resin coat on dentin, which blocks mechanical and biological stimuli to dentin-pulp-complex. 

4-methacryloxyethyl trimellitate anhydride

 

ADVANTAGES:

EASY, 35-SECOND BONDING

No etching, just one coat 

THIN BUT ROBUST FILM

Only 9 microns but almost no post-op sensitivity Though only a single application is required, the robust coat blocks both mechanical and chemical stimuli to dentin-pulp complex. The thin bonding layer results in aesthetic margins and perfect contacts between adjacent teeth.

HIGH BOND STRENGTH

Strong bonds to enamel, dentin and resin composite... thanks to its 4-META monomer Hybrid Bond penetrates the tooth to form 4-META hybrid layer and leaves the surface protective by a robust resin film.

INDICATIONS:

Hybrid Bond can be used in

Direct restorations of all types of composites:-

  • Class I , III, IV V cavities
  • Attrition at cutting edges
  • Diastema Closure

Indirect restorations:

As a protective coat for dentin under crown & bridge work for prevention of post-op pain

 

Features
  • No etching, just one coat
    The entire bonding procedure takes 35 seconds, start-to-finish.
    Chemically-activated Microbrushes® eliminate mixing.
  • Any composite, any curing light
    Halogen, Xenon (Plasma Arc) or even LED.
  • Thin but robust film
    Only 9 microns but almost no post-op sensitivity.
    The thin bonding layer results in aesthetic margins and perfect contacts between adjacent teeth. The robust coat blocks both mechanical and chemical stimuli to dentin pulp complex.
  • High bond strength.
  • Strong bonds to enamel, dentin and resin composites, thanks to 4-META ... a proven adhesive monomer.
Key Specifications

TECHNICAL DATA:

I. Bond Strength:

A. Micro Tensile Bond Strength

 1. Sound Dentin -44Mpa

2. Carious Dentin:

Affected Dentin - 43MPa

Infected Dentin -2.8MPa

B. Tensile Bond Strength

1.Enamel -13Mpa

2.Dentin -13 Mpa

II. Film Thickness - 9 microns with uniform thickness

III. Dentinal Tubules Sealing -100%

 

Safety

  • Sensitivity Hybrid Bond should not be used by clinicians or on patients who are methacrylate monomer-sensitive.
  • If signs of irritation such as redness appear, stop using it immediately and consult a physician.

 

Precautions

  • Hybrid Bond contains acidic methacrylate monomer.
  • Avoid contact of the Hybrid Bond components with soft tissue, skin or eyes.
  • Use of rubber dam is recommended. Contaminated skin or mucosa should be wiped off immediately with alcohol and then rinsed thoroughly with copious amounts of running water. In some cases contaminated mucosa or gingiva may whiten, which will usually disappear in a few days.
  • To minimize contamination during blowing or coating, place an evacuator near the treated tooth.
  • If Hybrid Brushes contact wet skin, the odor may remain.
  • If the Hybrid Bond components enter the eye, immediately rinse the eye thoroughly with running water.
  • Then the patient should be examined by an ophthalmologist.
  • Clinicians should use dental protective gloves.
  • Hybrid Base contains approx. 40% acetone.
  • Inhalation of a large amount of concentrated vapor may cause headache: therefore the area should be well ventilated.
  • In case of such severe inhalation, move to fresh air.

 Pulp protection

If the preparation approaches the pulp, apply a protective liner or base.

 Flammability

Hybrid Base is flammable. AVOID OPEN FLAME in use and storage. tApplications Use Hybrid Bond only for the applications recommended in the instructions.

 

TO GET THE BEST RESULTS:

Hybrid Brushes

Hybrid Brushes contain a bonding promoter and are an important component of Hybrid Bond. Always apply Hybrid Bond using Hybrid Brushes and do NOT substitute any other brushes. 

Storage

Store Hybrid Bond in a dark location between 4˚C and 30˚C, preferably in a refrigerator, but do NOT freeze Hybrid Bond. If frozen, phase separation will occur. High temperature, direct sunlight and high humidity should be avoided. Hybrid Brushes are slightly hydroscopic.

Volatility

Hybrid Base is highly volatile. Firmly recap the bottle immediately after use.

Contamination

To avoid contamination, do not mix the components with those of other materials, nor mix the bottle caps. Particularly, do not mix Hybrid Brushes with other mini-brushes. After use, dispose of leftover material. Once dispensed, do not return the materials to their original container.

Directions to use

Surface Preparation

Prepare tooth using an instrument such as fine-grit point so that the smear layer becomes minimal. After tooth preparation, wash and blow-dry the surface.

Note: The bond strength to enamel can be further improved by pretreatment of enamel for 5 - 10 seconds with a phosphoric etchant such as Super-Bond C&B Red Activator but do NOT use silica- thickened phosphoric etchant which will compromise the bond strength. Fluorinated enamel should be always etched as above.

 

Application of Hybrid Base

a) Dispensation

• Dispense one drop (up to 3 drops for a larger surface) of Hybrid Base in the well of a Plastic Dispensing Dish and firmly recap the bottle immediately.

• Stir the expressed liquid in the well with a Hybrid Brush for a few seconds. Note: The liquid in the mixing well should be used within 3 minutes to minimize evaporation.

b) Application

• After stirring with the Hybrid Brush, apply onto the prepared tooth surfaces and keep it moist for 20 seconds.

• Air-blow the solvents for 5 - 10 seconds until the tooth surfaces appear smooth and shiny. eLight-curing Irradiate light with a visible light curing unit. Note: Hybrid Bond is compatible with any currently available curing lights. With a fast light, the irradiation time should be shortened according to the instruction of the manufacturer and reflecting the above shorter irradiation time for direct restorations.

Light-curing

Irradiate light with a visible light curing unit.


packaging
  • 1 x 3ml Bottle
  • 100 x  mini brushes Hybrid Brushes
  • 5 x Plastic Dispensing Dish
Additional Information

Additional Information

Dispatch Date Next Day
Expiry Date N/A
COD Yes
Reviews

Related Products

There are no products matching the selection.

You may also be interested in

Tokuyama Shield Force Plus - Refill
tokuyama shield force plus - refill
Desentisizer
  • Rs.3,335.00

    Rs.2,850.00

    14.5% off

Sold Out

Fgm Desensibilize Nano P Desensitizing Agent
fgm desensibilize nano p desensitizing agent
Desensitizing Agent
  • Rs.1,425.00

    Rs.1,176.00

    17.5% off

Sold Out

Ivoclar Applicators Refill
ivoclar applicators refill
Micro Applicator Tips
  • Rs.118.00

Sold Out

Shofu Zirconomer Improved
shofu zirconomer improved
Reinforced Glass Ionomer
  • Rs.3,120.00

    Rs.2,800.00

    bulk price: Rs.2,795.00
    10.3% off
Shofu Fx Ultra Bulk Fill Glass Ionomer Restorative
shofu fx ultra bulk fill glass ionomer restorative
Glass Ionomer Cement - Type II
  • Starting at: Rs.2,750.00

    11.9% off
Shofu Glasionomer Cement Version 2 Improved Set
shofu glasionomer cement version 2 improved set
Glass Ionomer Cement
  • Rs.2,400.00

    Rs.2,280.00

    5% off
Shofu Hy-Bond Resiglass
shofu hy-bond resiglass
Resin Modified Glass Ionomer Luting Ceme...
  • Rs.3,360.00

    Rs.3,190.00

    5.1% off
Shofu P & R Repair Kit
shofu p & r repair kit
Light-Cure Bonding System
  • Rs.7,800.00

    Rs.6,255.00

    19.8% off
Top Dent Crown Cutting Tc Scissor
top dent crown cutting tc scissor
Top Dent Crown Cutting TC Scissor
  • Rs.712.00

Sold Out

API Stainless Steel Pluggers 21mm
api stainless steel pluggers 21mm
Pluggers
  • Starting at: Rs.280.00

    20% off

Recently Viewed Products